E-Z Patch® 2 Pool Deck Repair makes keeping your pool deck in top shape easy. Repair pool deck surfaces like Kooldeck®, simulated flagstone, simulated tile, simulated brick, etc., and more like a pro. E-Z Patch® 2 Pool Deck Repair is available in 24 different colors. The (S) Sand Buff color is most commonly used.
This product contains special acrylic modified materials with pozzolans (siliceous volcanic ash).Liquid Acrylic Bonder is included inside of kit.
If you’re having difficulty color matching your surface you may email us some pictures at info@e-zpatch.com. Please send about 3 pictures. Pictures should be about 2′ away. You may also mail us a minimum 1″ x 1″ piece of your surface to color match to our selection of colors. Please email us for the mailing address.
Below are our E-Z Patch® 2 Pool Deck Repair color options. All of our cement repair colors may be adjusted using any cement dye. Available in 1 lb., 3 lb., 10 lb. & 50 lb. sizes.
E-Z INSTRUCTIONS FOR A “KOOLDECK® TYPE HIGH-LOW TEXTURE:
1. Chip out any loose or flaking pooldeck.
2. Scrub area with water and brush using muriatic acid or laundry soap if needed.
3. Immediately rinse the area thoroughly and dab with sponge until damp only.
4. Add LIQUID CEMENT BONDER to DRY CEMENT MIX (use fractions = ¼ of the liquid cement bonder to ¼ of the dry mix). and add water and mix until you get the consistency of “stiff mashed potatoes” to release the dye color. (1 part liquid cement bonder to 3 parts water).
5A. FOR CRACK REPAIR: Rub E-Z PATCH® 2 into crack assuring deep penetration into crack (add more water to mix if needed). Remove excess immediately with a moist sponge. Rinse sponge often. Allow repair to dry, and then remove any residue with a dry cloth.
5B. FOR SMALL AREAS: Trowel about ¼” thick of E-Z PATCH® 2 onto the area, and then use your finger tips to “tap” E-Z PATCH® 2 all over to produce the “peaks” desired. If too wet to “peak”, wait or use a hair drier until it stiffens enough to retain “peaks”.
5C. FOR LARGER AREAS: Add more water and mix to produce the consistency of gravy. Apply with a cooldeck dash brush leaving “peaks”.
6. Remove excess from edges immediately with a moist sponge.
7. Allow the repair to dry (or use a hair drier) until the surface dulls, stiffens and doesn’t stick to your clean moist trowel. Trowel the tops of the “peaks”, starting with a light touch, increasing pressure a little at a time until you achieve the finished pattern desired. Keep your trowel moist and clean! If the repair is allowed to dry too hard to trowel, just mist or sprinkle the repair with water and trowel it again. Do not allow foot traffic for at least 24 hours and furniture for 3 days.
E-Z PATCH® 2 color will lighten when it dries but will darken somewhat as it cures. It takes 28 days for cement to cure.
To make a Custom Color with any of our cement type repair supplies, use any cement dye.
View our instructional repair video showing how to do this repair at www.e-zpatch.com
E-Z ANSWERS to some Frequently Asked Questions
Liquid Bonder is inside the jar
Product will cure faster in hotter weather, slower in cooler weather
Product is best stored between 40 degrees F and 90 degrees F
WARNING: CONTAINS CEMENT, AN ALKALINE SUBSTANCE IRRITATING TO EYES AND SKIN. CONTAINS ACRYLIC RESIN CEMENT BONDER. SHOULD PRODUCT CONTACT EYES, FLUSH THEM IMMEDIATELY AND REPEATEDLY WITH WATER AND CALL A PHYSICIAN. DO NOT TAKE INTERNALLY. IN CASE OF SKIN CONTACT, RINSE IMMEDIATELY WITH WATER. USE OF RUBBER GLOVES IS RECOMMENDED.
